Remington Models 700, Seven, 673 Owner’s Manual

Тагы и Book for:

MODELS 700, SEVEN, & 673
BOLT ACTION CENTERFIRE RIE;

Ze,

IMPORTANT!

This manual contains operating,

care, and maintenance instructions. To

ensure safe operation, any user of this

firearm must read and understand this manual before
using the firearm. Failure to follow the instructions and
heed the wamings in this manual can cause property
damage, personal injury, and/or death.

This manual should always accompany this firearm,
and be transferred with it upon change of ownership.

WARNING! Keep this firearm out of the reach of chil-
dren, unauthorized individuals, and others
unfamiliar with safe handing of firearms.

Genee THE TEN COMMANDMENTS OF
FIREARM SAFETY

KEE IMPORTANT PARTS OF THE FIREARM

HOW TO LOAD AND UNLOAD

usse LUBRICATION AND MAINTENANCE

BEER HOW TO OBTAIN PARTS AND SERVICE

A Tradition of Performance and Safety.

In 1816 Eliphalet Remington was confident he could make a flintlock that was as good or
better than any he could buy. His confidence was well founded. The barrel he handcrafted
set a new standard for firearm accuracy and spawned generations of products that have
made Remington® Arms America's leading gunmaker. While performance and style are
certainly hallmarks of Remington firearms, one factor ultimately drives their performance.
Safety. Eliphalet Remington never lost sight of the fact that his rifles were potentially
lethal and could kill someone if handled improperly. And after almost 200 years the Eliphalet Remington's first
same holds true for any firearm, including your new Remington. Eliphalet Remington's flintlock launched a proud tradition
first flintlock launched a proud tradition of accuracy and responsibility. ici

Safety is Critical to Performance.

A superbly crafted firearm is only as good as the hands that hold it. You can never be too careful. Shooting
accidents are often caused by careless oversights such as failing to control the direction of the muzzle, failing to
fully engage the safety, leaving ammunition in the chamber or using improper loads. These oversights can result
in the destruction of life, limb or property. There's no calling back a bullet once its been fired, so it's
critical that you know the principles of safe firearm handling and storage before you ever take your new
Remington firearm out of the box.

The proper use and performance of your firearm depends on correct assembly and maintenance, so it's critical
that you familiarize yourself with the information in this instruction book. Even if you're a veteran shooter with a
collection of Remington firearms, take the time to read this manual. Not all firearms are the same. That means
the first step in safe handling is to learn the features and requirements of your new Remington.

THE TEN COMMANDMENTS OF FIREARM SAFETY

The Ten Commandments of Firearm Safety should be etched in your memory forever. Let them govern your

action wherever and whenever you're involved with firearms. In the field. On the range. Or in your home.
Please take the time to review and understand these rules.

(Gy SG OM MA NU MERI
ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.

This is the most important firearm safety rule. A safe direction is one in which an accidental
discharge will not cause injury to yourself or others. Never allow your firearm to point at =
anything you don't intend to shoot. Be especially careful when you're loading or unload-

ing. Treat every firearm as if it were loaded. And make it a habit to know where the muzzle

is pointed at all times, even when your firearm is un-loaded. No one will be injured by an
accidental discharge if you keep your firearm pointed in a safe direction. It's as simple as

that.

Load your firearm only when you're in the field or on the target range and ready to discharge. Never let a loaded
firearm out of your sight or out of your hands. Unload it as soon as you're finished shooting - before you bring it
into your car, camp or home. Remember, unloading your firearm means unloading it completely, so there is no
ammunition in the chamber or in the magazine. Before handling a firearm or passing it to someone else, visually
check the chamber, receiver and magazine to be certain they do not contain ammunition. Always keep the firearm's
action open when not in use. Never assume a firearm is unloaded even if you were the last person to use it. Always
check for yourself.

® Let common sense rule when you carry a loaded firearm. If you're in a situation that could risk
accidental discharge - such as crossing a fence, wading through a stream or climbing a tree - always
unload your firearm. Never pull or push a loaded firearm toward yourself or another person. Never
carry a loaded firearm in a scabbard, detached holster or firearm case.

e Certain firearms (including some Remington? rifles and shotguns) are equipped with internal
security devices to prevent unauthorized use. In addition, some firearms owners use external
devices, such as cable locks and trigger blocks, for the same purpose. Even if you use such a _ |

к e f А AT Firearms should be stored in a
device, you should still keep your firearm unloaded when stored or not in use. And using internal secure place where children cannot

or external devices cannot substitute, however, for securing your firearms and ammunition in a sep- access them. A firearm safe is an
arate, locked location ideal way to secure your firearm

• Safe storage of firearms is just as critical as safe handling. Never store firearms loaded. Be sure
to keep your firearms in a secure place where unauthorized persons cannot get their hands on them without your knowledge.

• Take special care if there are children around. Children are fascinated by firearms. It's a natural curiosity that can have tragic
consequences when not properly supervised. Store your firearms in a locked firearm safe or some other location that physically
bars a child from gaining access.

e Ammunition should be stored and locked in a location separate from your firearm. Never leave an unsecured firearm or ammu-
nition in a closet, dresser drawer or under the bed. Remember, it is your responsibility to make sure that children and others
unfamiliar with firearms cannot get access to your firearm and ammunition.

fy COMMANDMENT

Don't RELY ON YOUR FIREARM'S SAFETY

Treat every Firearm as if it can discharge at any time, whether or not there's pressure on the trigger. Your firearm has been carefully
designed to maximize performance and safety. However, because a firearm's safety is a mechanical device, it could fail.

Human error is a more likely reason for a firearm's safety to fail. By mistake, you may think the safety is on when it really isn't. Or

the safety may have been disengaged without your knowledge. Or you could think your firearm is unloaded when there's actually a
cartridge or shell in it. A mechanical safety is not a substitute for common sense. It's merely a supplement to your proper handling
of a firearm.

Never touch the trigger on a firearm until you are ready to shoot. Keep your fingers away from the trigger when you're loading or
unloading. Don't pull the trigger when the safety is engaged or positioned between safe and discharge.

Before using your firearm, read this instruction book to understand the exact location and operation of your firearm's safety. Even
when the safety is on, maintain control of your loaded firearm and control the direction of the muzzle. In other words, don't rely on
your safety to justify careless handling. If your firearm's internal mechanisms are broken or have been altered, your firearm may dis-
charge even when the safety is on. Remember, you and your safe firearm handling practices are your firearm's best safety.

fiy OO MAN ni

BE SURE OF YOUR TARGET AND WHAT'S BEYOND IT.

You can't stop a shot in mid-air, so never discharge unless you know exactly where
your shot is going and what it will strike. Never discharge at a sound, a movement or a

VS patch of color. À hunter in camouflage can easily be mistaken for a target by an impul-
sive shooter. Before you pull the trigger, be absolutely sure of your target and what's

behind it. Make sure the shot has a backstop such as a hillside or dense mate-

rial like sand. Remember, bullets can travel great distances with tremendous velocity. Know how far
your shot will go if you miss your target or the bullet ricochets.

(pO MM ANDMENT

Use PROPER AMMUNITION

Every firearm is designed to use a certain caliber or gauge of ammunition. Using the wrong ammunition, mixing ammuni-
tion or using improperly reloaded ammunition can cause serious personal injury or death. And it only takes one cartridge
or shotshell of the incorrect caliber or gauge, or which has been improperly reloaded, to destroy your firearm. It's your
responsibility to make sure the ammunition you use exactly matches the caliber or gauge of your firearm. Refer to this

instruction book to find out the specific requirements of your firearm. Always read and heed the instructions on ammu-
nition boxes.

Confusing shells or cartridges can cause serious personal injury or death and destroy your firearm. Examine your shells
or cartridges closely and use only the precise caliber or gauge for your specific firearm. For example, suppose you acci-
dentally loaded a 20 ga. shell into a 12 ga. shotgun. Because the 20 ga. shell is too small for the chamber, the 20 ga.
shell could travel down the barrel and get lodged in the bore. If you then loaded a standard 12 ga. shell behind it and
fired, the 12 ga. shot will slam into the lodged 20 ga. shell and may cause the barrel to explode right in your hand. This
is commonly called a 12/20 burst, and it can kill you.

Check all ammunition before you load it to make sure it matches your firearm's requirements. Every Remington® cartridge
and shell is head-stamped with its caliber or gauge for easy identification. Likewise, you'll find the caliber or gauge of
your new Remington firearm imprinted on the barrel.

Reloading Requires Extra Diligence.

If you're an ammunition reloader you are responsible for personally ensuring that the loads and components of your
reloaded ammunition meet your firearm's factory-tested standards. Never use ammunition, which has been reloaded by
someone else!

Many shooters handload as a hobby or to save money on commercial, factory-made ammunition. However, it requires a
thorough knowledge of reloading procedures and a deep respect for the explosive potential of gunpowder.

Firearms are designed, manufactured and proof-tested to standards based on factory-loaded ammunition. Handloaded or
reloaded ammunition that deviates, either intentionally or accidentally, from load or component recommendations can
be very dangerous.

Reloaders must observe all possible safety precautions and practices related to the proper handling of explosives.
Whether you're a seasoned reloader or just starting out, you should study the subject, watch reloading demonstrations
and talk to experienced reloaders.

The first rule of reloading is to always follow the manufacturer's instructions for the components you're using. They'll tell
you to follow certain guidelines. Namely:
1. Don't mix or substitute powders or primers.
2. Don't use unknown or substandard components.
3. Use only suitable components that have been factory-tested by reputable ammunition,
powder and bullet manufacturers.
4. Always be sure to use the manufacturer's recommended recipe when reloading.

Not following these guidelines could result in severe injury to yourself or severe damage to your firearm. Dangerously high
pressure and explosions can result from an overcharge of powder or other deviations from established reloading guidelines.
Be very careful. The process of reloading exposes you to environmentally hazardous material. Lead, which is known to cause
cancer and birth defects, is the most common substance in bullets and shot. It is important to handle lead bullets and shot
with extreme care. Work only in a well-ventilated area and always wash your hands after exposure and before eating. Never
smoke while reloading.

Primers and powders are also highly toxic and flammable. So after reloading be sure to clean up all materials from your
work area. Don't leave primer or powder spills anywhere on the floor or bench top. Dispose of all waste material in accor-
dance with the manufacturer's recommendations.

Finally, when reloading or handloading concentrate on what you're doing at all times. Do not be distracted by talking to oth-
ers, listening to the radio or watching TV while reloading. Never reload after consuming alcoholic beverages or drugs of
any kind. You are working with extremely hazardous materials and you can't risk even a few seconds of distraction.
Remember, if you reload, you are the ammunition manufacturer and you are responsible for the performance and safety
of your reloaded ammunition.

Gig he o Mm MANDO MENT
IF YOUR FIREARM FAILS TO DISCHARGE WHEN THE TRIGGER IS PULLED, HANDLE WITH CARE.

If for some reason the ammunition doesn't discharge when you pull the trigger, stop and remember the 1st
Commandment of Firearm Safety - always keep the muzzle pointed in a safe direction. Keep your face away from
the breech, then place the safety on, carefully open the action, unload the firearm and dispose of the cartridge
safely. Remember that anytime there's a shell in the chamber, your firearm is loaded and ready to use. Even if
you tried to shoot and your firearm didn't discharge, treat your firearm as if it could still discharge.

(y AN DAME A ROME NT
ALWAYS WEAR EYE AND EAR PROTECTION WHEN SHOOTING.

Your sight and hearing risk injury from shooting and should be protected at all times.
Wear protective shooting glasses to guard against falling shot, clay target chips,
powder residue, ruptured cartridge cases and even twigs and branches in the field.
Also be sure to wear eye protection when you're disassembling or cleaning a
firearm so that tensioned parts (like springs) and cleaning solvents don't come in
contact with your eyes. Continued exposure to shooting noise can permanently
damage your hearing. On the range, where shooting volume is the loudest, be sure to use the maximum pro-
tection of a headset. Learn to use ear protection at all times.

(Gn COMMAND MERI
Be SURE THE BARREL IS CLEAR OF OBSTRUCTIONS BEFORE SHOOTING.

Before loading your firearm, open the action and make sure there's no ammunition in the chamber or magazine.
Check the barrel for any obstructions or debris. Even a small amount of snow, mud, excess lubricant or grease
in the bore can dangerously increase pressure and cause the barrel to bulge or burst when firing. Use a clean-
ing rod and patch to wipe away anti-rust compounds or any other residues or obstructions in the barrel. Never
try to shoot out an obstruction by loading another shell and firing!

When firing, rely on your instincts. If the noise or recoil of your firearm seems weak, stop everything, unload
your firearm and be sure nothing is lodged in the barrel. Remember the 12/20 burst? That's what can happen
when the barrel is obstructed. Always be sure you're using the correct ammunition in your firearm and that it's
free of obstructions.

(y COM MAND MENT
Don't ALTER op MopiFY Your FIREARM AND HAVE IT SERVICED REGULARLY.

Your firearm has been designed to operate according to certain factory specifications. You'll jeopardize your safe-
ty and that of others around you by attempting to alter its trigger, mechanical safety or other mechanisms. So
never alter or modify your firearm in any way.

Like any mechanical device, a firearm is subject to wear. It must be maintained
and periodically serviced to assure optimum safety and performance. Only a
qualified service facility should service, repair or modify your Remington
firearm. Consult your instruction book for instructions on how to send your
firearm to the factory or for the location of the nearest Remington authorized
repair station.

Proper cleaning and lubrication are also important to firearm maintenance and
are necessary to assure accuracy, safety and reliability. Before cleaning,
always make sure that your firearm is completely unloaded. Always clean the
barrel from the chamber end to the muzzle when possible.

Make it a practice to clean your bore every time you're going to shoot. Be sure to clean your entire firearm before
and after long-term storage and no less than once a year. It's also important to clean your firearm whenever it's been
exposed to adverse conditions such as rain, dirt, mud, snow, sleet or saltwater.

For safe and dependable operation of your firearm, all parts of your firearm must be properly cleaned and lubri-
cated. Periodically inspect the internal workings of your firearm to be sure they're clean and free of rust,
unwanted dirt and debris.

Use recommended lubricants on your firearm and do not over-lubricate. Excessive use of a non-recommended lubri-
cant could adversely affect the function and safe operation of your firearm. Remember, you are responsible for
the proper care and maintenance of your firearm. Failure to properly maintain your firearm cannot only damage
or ruin your firearm, it can expose you and others to unnecessary risks of personal injury or death.

COMMANDMENT
LEARN THE MECHANICS AND HANDLING CHARACTERISTICS OF YOUR FIREARM.

Not all firearms are alike. They have different mechanical characteristics that dictate how you should carry and handle
them. Anyone who plans to use a firearm should first become totally familiar with the type of firearm it is and the
safe handling procedures for loading, unloading, carrying, shooting and storing it.

Before you even unpack your new Remington firearm, read this instruction book from
cover to cover and familiarize yourself with the different component parts of the
firearm. Then read, understand and follow the Ten Commandments of Firearm
Safety in this manual.

WARNING! Discharging firearms in poorly ventilated areas, cleaning firearms
or handling ammunition may result in exposure to lead, a substance known
to cause birth defects, reproductive harm, cancer and other serious physi-
cal injury. Have adequate ventilation at all times. Wash hands thoroughly
after exposure.

SHOOT SOBER!!

There's one other rule that must be followed when handling firearms. In fact, respect for this rule is necessary in
order to effectively practice the Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER! Firearms and
alcohol or drugs make a deadly combination. Never consume anything that would mildly impair your judgment or
physical coordination when you're using a firearm. A staggering percentage of the shooting accidents that occur
every year involve alcohol or drugs. Be smart. Always shoot sober and stay alive.

WARNING! Failure to follow any of these safety rules may cause personal injury or death to the shooter or
bystander and damage to property. Do not use a firearm until you fully understand and practice the Ten
Commandments of Firearm Safety. If you have any questions about the safe use of a Remington firearm, contact us
at www.remarms.com

DON'T KEEP THIS TO YOURSELF.

Now that you're a firearm owner you have the obligation to help ensure that shooting sports are safe for everyone - par-
ticipants and bystanders alike. You can do that by practicing these principles of firearm safety and passing them on
to others - especially new shooters. Set an example for beginners. Be a guide to their safe entry into the exciting
world of shooting sports. Invest your time and patience for the love of the sport and for its future. After all, it's your
love of the sport that led you to buy a new Remington.

Firearm ownership is a right and privilege. It's a right guaranteed in this nation's Constitution. It's a privilege, which
carries with it a personal responsibility to use your firearm in a way which will ensure your safety and the safety of
others. The preservation of this right and privilege depends on the personal commitment of you and your fellow
shooters to the safe and responsible use of firearms. Let the Ten Commandments of Firearm Safety outlined in the
manual guide you at all times. Teach and promote these rules whenever you can. Remember, firearm safety depends
on you! That's the only way to really enjoy your new Remington firearm and to preserve sport shooting as we know
it today.

Remington: Bolt Action Centerfire Rifle
Congratulations on your choice of a Remington? With proper care, it should give you many years of dependable use
and enjoyment.

Picture 1 — This picture shows the main parts of a REMINGTON BOLT ACTION RIFLE. The picture will aid in understanding the instructions in this book.

BOLT ASSEMBLY EJECTION PORT FRONT SIGHT

RECEIVER CHAMBER REAR SIGHT

STOCK. SAFETY MECHANISM

/

BARREL

N

MAGAZINE FLOOR PLATE

TRIGGER

BOLT HANDLE TRIGGER GUARD. BOLT STOP RELEASE

PICTURE 2
Cartridge Head Primer А This picture shows the
: Cartridge parts of the ammunition.
К . Rim Bullet
Caliber Marking Head Case

Important Parts of the Firearm
The Salety Mechanism

The safely mechanism provides protection against accidental or unintentional discharge under normal usage
when properly engaged and in good working order. The safety mechanism is
PICTURE 3 not a substitute for following the rules of safe firearm handling.

To engage the safety mechanism, pull the safety mechanism fully to the rear
towards the "S" position. See Picture 3.

Always place the safety mechanism in the "S" position before handling,
“5” position ` loading or unloading the firearm.
When you are ready to discharge the PICTURE 4

firearm, push the safety mechanism forward towards the "F" position to disengage d
the safety mechanism. See Picture 4.

Do not touch the trigger while moving the safety mechanism. Your fingers and
all other objects should be kept outside of the trigger guard and away from the
trigger until you are actually ready to discharge by pulling the trigger.

Never pull the trigger when the safety mechanism is in the "S" position.

WARNING! The firearm will discharge when the trigger is pulled and the safety mechanism is in the "F" position.
Even when the safety mechanism is in the "S" position, careless handling can cause the firearm to discharge. SEE
THE TEN COMMANDMENTS OF FIREARM SAFETY ON PAGE 2.

The Security System

D

“F” POSITION

A SECURITY SYSTEM DOES NOT ELIMINATE THE NEED FOR SAFE FIREARM HANDLING AND STORAGE, INCLUD-
ING KEEPING THIS AND EVERY FIREARM UNLOADED AND LOCKED IN A SECURE PLACE WHEN NOT IN USE. READ
AND FOLLOW THESE AND OTHER SAFETY RULES IN THIS INSTRUCTION BOOK. FAILURE TO READ, UNDERSTAND
AND OBEY THESE RULES CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH. SEE THE TEN COMMAND-
MENTS OF FIREARM SAFETY ON PAGE 2.

To Install The Bolt Assembly: The bolt assembly locks the cartridge into the chamber.
1. Always point the firearm in a safe direction.
` 2. Place the safety mechanism in the "5" position.
3. Align the lugs on the bolt assembly with the receiver. See Picture 8.
4.Slide the bolt assembly into the receiver and push all the way in.

5. To place the bolt assembly in the closed position, push the bolt handle down.
NOTE: The security system must be disengaged to close the bolt. The Red dot will show.

To Remove The Bolt Assembly: PICTURE 8
1. Always point the firearm in a safe direction.
2. Place the safety mechanism in the "S" position.
3. Do not touch the trigger while moving the safety mechanism.
4. Raise the bolt handle.
5. Pull the bolt handle all the way back.
6. Push the bolt stop release in the trigger guard. See Picture 8.

7. Slide the bolt assembly from the firearm. BOLT STOP RELEASE
The Trigger Assembly
Pulling the trigger discharges or “fires” the firearm. The trigger assembly
on your rifle may permit the adjustment of the trigger PICTURE 9

pull force by the user (see Picture 9 to determine if your
С] trigger assembly is user adjustable). On rifles that are so
equipped, the trigger pull force is adjustable without
removing the action from the stock.

WARNING! Only the trigger pull force is adjustable. For safetys sake, NEVER
make adjustments or alterations to any other parts of the trigger assembly or rifle.

WARNING! NEVER place your finger on the trigger unless you are going to dis-
charge the firearm.

To Adjust The Trigger Pull Force:

The trigger of your rifle has been preset at the factory in conformity with industry guidelines to have a trigger pull force of
3 pounds or more. However, for competition target shooters firing the rifle from a secure stationary rest in a controlled environ-
ment, the trigger pull force can be adjusted downward by the user or a qualified gunsmith using the procedure set forth below.
WARNING! Adjustment of the trigger pull force in this rifle below 3 pounds should only be made for a rifle to be
used in competitive target shooting and discharged from a secure stationary rest in a controlled environment. For
any other purpose, including use in the field, the trigger pull force on your rifle should NEVER be reduced below
3 pounds. Remember — regardless of the amount of trigger pull force, ALWAYS keep the muzzle of your rifle
pointed in a safe direction to prevent injury or death caused by an unintended or accidental discharge.
WARNING! With the safety mechanism in the SAFE or “S” position, check the chamber and magazine of the rifle
to make sure there are no cartridges in the rifle. NEVER attempt to adjust the trigger pull force on a loaded rifle.

TRIGGER PULL FORCE
ADJUSTMENT SCREW

1. To adjust the trigger pull force, place the provided wrench's hex key
in the socket of the adjustment screw. A standard 1/16” hex key can aa
also be used to make this adjustment. PICTURE 10

2. Adjust the trigger pull force to the desired setting by turning the
adjustment screw. Turning the trigger pull adjustment screw coun
terclockwise will lighten the trigger pull force. Turning the trigger
pull adjusting screw clockwise will increase the trigger pull force.
The trigger pull will change by approximately 1 Ib for each full turn
of the adjustment screw.

3. After making an adjustment, remove the wrench from the socket of the adjustment screw.

4. After ensuring the firearm is unloaded, dry “fire” the rifle by pulling the trigger and cycling the bolt,

several times after making an adjustment to ensure the trigger pull force spring is seated.

5. Check the trigger pull force with a force gauge or deadweight.

6. Repeat step 5 several times to ensure the proper trigger pull force is maintained.

T. If the setting is unsatisfactory, follow the instructions outlined in steps 2-6 until you are satisfied.
WARNING: If the proper trigger pull force cannot be maintained from pull to pull, then return the firearm to the
factory for service. Do not use your rifle if the trigger pull force can not be maintained.

WARNING: The minimum achievable trigger pull force is preset at the factory and must not be altered.
WARNING: Be sure to note if you have adjusted the trigger pull force below 3 pounds when you store your
rifle for any period of time. If you expect at any time to loan or sell your rifle or to use the rifle for anything

other than competition target shooting from a secure, stationary rest in a controlled environment, you should
readjust the trigger pull force to at least 3 pounds.

The Barrel

The inside of the barre! must be clean and free of obstructions.

I. TO CHECK THE INSIDE OF THE BARREL:
1. Always point the firearm in a safe direction.
2. Place the safety mechanism in the "S" position.
3. Raise the bolt handle.
4. Pull the bolt all the way back.
5. Remove any ammunition from the chamber or magazine. See page 12.
6. Remove the bolt.
7. Inspect the barrel from the chambered end. See Picture 1 on page 7.

ll. TO REMOVE OBJECT FROM INSIDE THE BARREL:
1. Use correct size cleaning rod.
2. Push cleaning rod from the chamber end all the way through the barrel, until the rod comes out of the muzzle.

3. If an object cannot be easily pushed out of the barrel with a cleaning rod, return the firearm to the factory
or a REMINGTON AUTHORIZED SERVICE CENTER.

WARNING! NEVER try to remove an object from the barrel by loading another cartridge and firing. This may
cause the barrel to burst or a cartridge case to rupture and cause serious personal injury or death.

Ш, TO CLEAN THE BARREL FOLLOW THE INSTRUCTIONS SHOWN ON PAGE 14.
Before loading the firearm, make sure the inside of the barrel is free of dirt or other obstructions.

To Load the Firearm

There are three types of Model 700 rifles:

(1) with a FLOOR PLATE, (2) without a FLOOR PLATE and
(3) with a DETACHABLE MAGAZINE BOX.

I. ТО LOAD ONE CARTRIDGE ONLY:
1. Always point the firearm in a safe direction.
2. Place the safety mechanism in the "S" position.
3. Raise the bolt handle.
4. Pull the bolt handle all the way back.

5. Place one cartridge of the correct caliber on the magazine follower or in the chamber. See Picture 11.

6. Slide the bolt handle forward, then push the bolt handle down to lock the cartridge into the chamber.
THE FIREARM IS NOW LOADED WITH A ROUND IN THE CHAMBER.

7. To prepare to discharge the rifle, place the safety mechanism in the "F" position.
THE FIREARM WILL DISCHARGE WHEN THE TRIGGER IS PULLED AND THE SAFETY MECHANISM IS IN
THE “F” POSITION.

Il. ТО LOAD THE CHAMBER AND MAGAZINE:
ways point the firearm in a safe direction.
ace the safety mechanism in the "S" position.
aise the bolt handle.
ull the bolt handle all the way back.
ush four cartridges of the correct caliber, one at a time, into the
agazine. If the firearm is a magnum, you can only load three
artridges. If the firearm is a 17, 222, or 223 caliber, the magazine will hold five cartridges. Keep the bul-
ets aligned toward the chamber. See Picture 11.
6. Place one cartridge into the chamber.
. Use your fingers to push the cartridges in the magazine all the way down. Slowly slide the bolt assembly
forward so that the bolt slides over the top of the cartridges in the magazine.

8. Push the bolt handle down.
THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED.
WARNING! Always check the cartridge for the correct caliber before loading the firearm.

9. To discharge the firearm place the safety mecchanism in the "F" position.0
THE FIREARM WILL DISCHARGE WHEN THE TRIGGER IS PULLED AND THE SAFETY MECHANISM IS IN
THE “F” POSITION. PICTURE 12
ALTERNATE METHOD TO LOAD THE CHAMBER AND MAGAZINE:
(FOR MODELS 700: WITH DETACHABLE MAGAZINE BOX)

PICTURE 11
LOAD CARTRIDGE AS SHOWN

DUE

3 © 0

em ©

E
c

1. Always point the firearm in a safe direction.
2. Place the safety mechanism in the "S" position.
3. Raise the bolt handle. РА Мы LY
4. Pull the bolt handle all the way back. PRESS BOTH MAGAZINE LATCHES
5. Press both magazine latches inward and pull the magazine box from ме
the firearm. See Picture 12.
6. Push four cartridges of the correct caliber, one at a time, into the magazine box, pushing the cartridges to
the rear of the magazine. If the firearm is a magnum, you can only load three cartridges. Keep the bullets
aligned toward the chamber. See Picture 11.
7. Place the magazine box into the trigger guard opening and push it until both latches snap into the fully
latched position.
THE MAGAZINE IS NOW FULLY LOADED.
8. Place one cartridge of the correct caliber into the chamber. See Picture 11.
9. Use your fingers to push the cartridges in the magazine all the way down. Slowly slide the bolt assembly
forward so that the bolt slides over the top of the cartridges in the magazine.
10. Push the bolt handle down to lock the cartridge into the chamber.
THE CHAMBER AND MAGAZINE ARE NOW FULLY LOADED.
11. To prepare to discharge the firearm, place the safety mechanism in the "F" position.
THE FIREARM WILL DISCHARGE WHEN THE TRIGGER IS PULLED AND THE SAFETY MECHANISM IS IN
THE “F” POSITION.

WARNING: Always check the cartridge for the correct caliber before loading the firearm.

10

To Unload the Firearm iion

ei BR
There are three types of Model 700™ rifles: (1) with a FLOOR PLATE, (2) REI

without a FLOOR PLATE and (3) with a DETACHABLE MAGAZINE BOX. ey em

INSTRUCTIONS FOR THE MODELS WITH A FLOOR PLATE: e

FLOOR PLATE LATCH / | \
" : " Я d GAZINE FOLLOWER |
1. Always point the firearm in a safe direction. A CLIE mm M КООН РЕАГЕ
2. Place the safety mechanism in the "S" position.
3. Raise the bolt handle. PICTURE 14
4. Place one hand over the top of the ejection port.
5. Slowly pull the bolt handle rearward with your other hand to

remove the cartridge from the chamber.

6. Hold cartridge and remove it from the firearm.

7. Place the safety mechanism in the "S" position. SP \

8. Place your hand under the floor plate. FLOOR PLATE LATCH / / \

9. Push the floor plate latch to release the floor plate. See MAGAZINE FOLLOWER / Coven
Picture 13 for Model 700 or Picture 14 for the Model Seven™ MAGAZINE SPRING

& Model 673™ . The magazine spring and follower will be
released from the magazine.

10. Remove released cartridges.
11. Push in the magazine follower, then close the floor plate.
WARNING: Check the chamber and the magazine to make sure there are no cartridges in the firearm.

INSTRUCTIONS FOR THE MODELS WITHOUT A FLOOR PLATE:

1. Always point the firearm in a safe direction.

2. Place the safety mechanism in the "S" position.

3. Raise the bolt handle.

4. Place one hand over the top of the ejection port.

5. Slowly pull the bolt handle rearward with your other hand to remove the cartridge from the chamber.

6. Hold cartridge and remove it from the firearm.

7. Always keep the muzzle pointed in a safe direction. Push the bolt handle slowly forward until the cartridge

is released from the magazine.

CAUTION: The cartridge may slide into the chamber if the bolt is pushed too far forward. See NOTE below.

8. Pull the bolt handle fully rearward and remove the cartridge from the ejection port.

9. Repeat Steps 7 and 8 until the magazine is empty.
WARNING! Check the chamber and the magazine to make sure there are no cartridges in the firearm.

NOTE: If the bolt is pushed all the way forward and a cartridge slides into the chamber, the firearm can be
discharged. Normally, the cartridges will slide out of the chamber when the bolt is pulled back. If the cartridge
remains in the chamber, point the muzzle in a safe direction, slide the bolt forward all the way and push the
bolt handle down to close the bolt. Then repeat Steps 1 through 9 above.

INSTRUCTIONS FOR THE MODELS WITH A DETACHABLE MAGAZINE BOX:

1. Always point the firearm in a safe direction.
2. Place the safety mechanism in the "S" position.

11

3. Raise the bolt handle.
4. Place one hand over the top of the ejection port.
5. Slowly pull the bolt handle rearward with your other hand to remove the cartridge from the chamber.
6. Depress both latches to release magazine box. See Picture 12 on page 11.
7. Remove all cartridges from the magazine box.
8. Replace the magazine box.
WARNING! Check the chamber and the magazine to make sure there are no cartridges in the firearm.

To Adjust Sights
<> TO ADJUST THE REAR SIGHT:
Move the rear sight in the same direction as you need to
move the bullet on the target. See Picture 15.

NOTE: For more on ballistics and trajectory, see the REMINGTON®
catalog.

REAR SIGHT APERTURE PICTURE 15
WINDAGE SCREW ` —

REAR SIGHT SLIDE
ELEVATION SCREW

For the Model 673" ONLY. The rear sight elevation screw is located
ahead of the rear sight aperture. The point of aim is adjusted by using a
1/16" hex wrench. To raise the point of impact turn the elevation screw

8 А E PICTURE 15:
clockwise. See Picture 15a. a

REAR SIGHT APERTURE

The ventilated rib is screwed to the barrel and is isolated through the use еа SA

of synthetic buffers, both above and below the rib. The design allows the
rib to “float”. In this way the barrel moves independently of the rib
ensuring accuracy. Disassembly is not recommended.

TELESCOPIC SIGHTS:
The top of the receiver has holes for the installation of telescopic
sights.
POSITION ON ADJUSTMENT
TARGET

. Loosen the elevation screw on the
right side.

Ф

Bullet hits above
the center. C:

. Slide the rear sight down (backward)

on the ramp.
Tighten the elevation screw.

©

. Loosen the elevation screw on the

right side.

. Slide the rear sight up (forward)

Bullet hits below on the ramp.
the center. c. Tighten the elevation screw.
a. Loosen the windage screw on the
e) right side.
b. Slide the rear sight aperture to the
Bullet hits to right.
the left. c. Tighten the windage screw.

Ф

. Loosen the windage screw оп the

right side.
. Slide the rear sight aperture to the
Bullet hits to left.
the right. c. Tighten the windage screw.

12

Lubrication

Over-lubrication should be avoid-
ed at all times. A light application of
Oil helps to prevent rusting.

WARNING! Excessive use of a lubri-
cant could adversely affect the func-
tion and safe operation of your
firearm. Failure to prop- ^W
erly maintain your
firearm can not only
damage your firearm, it
can expose you and oth-
ers to unnecessary risks
of personal injury or death.

When the firearm is to be stored, it
should be carefully cleaned and thor-
oughly oiled. Outside metal surfaces
should be wiped with oil occasionally.

To Clean the Barrel

When the firearm is to be reused, all
excess lubrication must be removed.
The chamber and bore must be thor-
oughly wiped dry.

For safe and dependable operation of
your firearm, the barrel and action
must be cleaned periodically.

WARNING! The use of a non recom-
mended lubricant or cleaner could
adversely affect the function and safe
operation of your firearm. Do not use
congealing lubricants. The use of non-
congealing lubricants is strongly rec-
ommended.

WARNING! Check the chamber and magazine to make sure there are no cartridges in the firearm.
1. Use the equipment provided in a good cleaning kit. For recommendations, see your REMINGTON

AUTHORIZED SERVICE CENTER.

2. Remove the bolt assembly. See instructions on page 9.

3. Select the correct caliber cleaning brush and attach the brush to the cleaning rod.

4. Place the cleaning brush into the firearm cleaning solvent.

NOTE: Barrel should lay horizontally with the ejection port facing down during cleaning. Always clean the

barrel from the chamber end to the muzzle.

5. Push the cleaning brush through the barrel several times.
move brush from rod, attach tip with patch, and push through the bore.

peat several times, using a new cleaning patch each time, until the patch is not dirty.
ush a clean patch saturated with oil through the barrel.

CD CD

6.R
T.R
8.P

9. Push a clean dry patch through the barrel to remove excess lubricant.
10. Apply a thin coat of oil to the outside of the barrel with a soft clean cloth.
11. After cleaning the barrel, clean the receiver and the trigger assembly.
WARNING! This firearm should be checked periodically by the RemArms, LLC. or a REMINGTON AUTHORIZED SERV-
ICE CENTER. This will ensure proper inspection and any necessary replacement of worn or

damaged parts.

To Clean the Receiver and The Trigger Assembly

1. Always point the firearm in a safe direction.

2. Place the safety mechanism in the "S" position.
3. Remove the bolt assembly. See instructions on page 9.

4. Turn the rifle upside down.
5. Remove the stock screws. See Picture 16.

6. Lift the stock away from the receiver and the trigger assembly.

MODELS WITHOUT A FLOOR PLATE ONLY:

Remove the magazine spring and follower from the receiver.

NOTE: Clean and lubricate the receiver and the trigger assembly as a unit.

Do not remove the trigger assembly from the receiver.

oroughly spray the receiver inside and out with Action Cleaner and

ow to dry.

8. Thoroughly spray inside the trigger assembly at the four points

specified in Picture 17 with Action Cleaner.

9. Place the safety mechanism in the discharge “F” position. Pull the trigger

rearward and release multiple times.

10. Pull and hold the trigger rearward. Then using a small punch or screw-
driver depress the sear
(Lubrication Point 1 in Picture 1

11. Release the trigg
position multiple times.

12. Again thoroughly spray inside the trigger assembly at the four
points specified in Picture 17 with Action Cleaner. Air dry or use
compressed air to thoroughly dry the trigger assembly.

13. Place a drop of oil in each of the four points in the trigger assembly
specified in Picture 17.

14. Place the safety in the fire “F” position. Pull the trigger rearward and
release multiple times. Ensure the trigger returns completely to the for-
ward position each time. If the trigger does not completely return,
reassemble the rifle and return it to a Remington® Authorized
Service Center.

7) and release multiple times.

Place a drop of \
oil at the 4 points
shown

PICTURE 16
MODEL 700

tl

i ? |
` screws `

=

` screws `

MODEL SEVEN & 673

= /
SCREWS

er and operate the safety mechanism from the “F” to the "S"

PICTURE 17

WARNING! If the trigger does not fully return to the forward position each time it is released, then your rifle is NOT in a safe

operating condition and it must NOT be used until you have had it inspected by a Remi

of a firearm in an unsafe operating condition may result in injury or death to you or

damage to the firearm.

15. If the trigger completely returns as specified in operation 14, pull and ho
small punch or screwdriver depress the sear and release multiple times.
upward position without hesi
it to a Remington Authorized Service Center.

ngton Authorized Service Center. Use
a bystander and severe

d the trigger rearward; using a

The sear must return to the full
ation. If the sear does not freely return, reassemble the rifle and return

WARNING! If the sear does not return to the full upward position without hesitation,
operating condition and it must NOT
Use of a firearm in an unsafe operati
damage to the firearm.

16. If the sear freely returns to the
the safety from the fire “F” to th
safety detent spring must posit
in a position anywhere between

fire ^F" position after repeating operations 8 thru 16, return the firearm
Service Center for an inspection of the safety and the trigger assembly.
T7. P.

trigger assembly and receiver. Wipe off excess oil.

14

then your rifle is NOT in a safe

be used until you have had it inspected by a Remington Authorized Service Center.
ng condition may result in injury or death to you or a bystander and severe

full upward position as specified in operation 15, release the trigger and operate

e safe "S" position multiple times. The safety mechanism must operate freely. The
ion the safety in the full safe "S" or fire “F” position. The safety should not remain
the full safe "S" or fire "F" position. If the safety does not freely return to the full
safe “S” or fire “F” position, repeat operations 8 thru 16. If the safety does not freely return to the safe “S” or

to a Remington Authorized

ace the safety mechanism in the safe "S" position and lightly spray oil on all the external surfaces of the

TO ASSEMBLE MODELS WITHOUT A FLOOR PLATE:
1. Always point the firearm in a safe direction.
2. Place the magazine follower and the spring into the magazine.
3. Place the stock over the receiver and trigger assembly.
4. Replace and tighten the trigger guard (stock) screws.
WARNING! Before you replace the bolt assembly, make sure the barrel is free from obstructions.
5. Replace the bolt assembly. See instructions on page 9.

TO ASSEMBLE MODELS WITH A FLOOR PLATE ONLY:
Place the magazine all the way into the bottom of the receiver.

MODELS WITH FLOOR PLATE OR DETACHABLE MAGAZINE:
1. Always point the firearm in a safe direction.
2. Assemble the trigger guard assembly on the stock.
3. Place the stock over the receiver and trigger assembly.
4. Replace and tighten the trigger guard (stock) screws.
5. Close the floor plate or replace detachable magazine.

WARNING! Before you replace the bolt assembly, make sure the barrel is free of obstructions.

6. Replace the bolt assembly. See Instructions on page 9.
WARNING! After cleaning the trigger assembly, check the chamber and magazine to make sure there are no
cartridges in the firearm. Place the safety mechanism in the "F" position. Close the bolt smartly. The firing pin
must remain cocked. To check, pull the trigger. The firing pin must release. Repeat the test at least ten times.
If the firing pin will not remain cocked when the bolt is closed smartly, return the firearm to the factory or a
REMINGTON AUTHORIZED SERVICE CENTER.

Cleaning Frequency

1. After discharging firearm.
2. Before and after long term storage.
3. When the rifle has been subjected to adverse conditions such as shooting in the rain, snow,
sleet or saltwater areas.
4. When the rifle is exposed to dirty conditions such as lying on the ground outdoors, being
dropped in mud, etc.
NOTE: While the Model 700™ and Model Seven™ Stainless Synthetic Rifle have been designed and manufactured
to provide improved corrosion protection, only proper care will keep your firearm in good operating condition
and maintain its appearance. After extensive use, the protective coating on plated parts may be worn
sufficiently to reduce corrosion protection. Such worn parts should be replaced to assure the integrity of
the corrosion protection.

WARNING! After each use, follow the lubrication and maintenance direction in this instruction book. If the
firearm is immersed in water, it must be thoroughly cleaned and lubricated as soon as possible. In case of
salt- water immersion, first flush all parts with fresh water, then dry, clean and lubricate the firearm. If the
firearm does not function properly, have it corrected by a REMINGTON® AUTHORIZED SERVICE CENTER before
further use. Failure to follow this warning may lead to firearm malfunctions which could result in serious per-
sonal injuries or death and damage to the firearm.

15

Instructions for Cleaning the Bolt Assembly —

TO DISASSEMBLE THE BOLT ASSEMBLY: PLACE СОМ PULL
1. Always point the firearm in a safe direction. de Q
2. Remove the bolt assembly from the firearm. See instructions on GC
page 9. VISE 2
3. Place the notch on the firing pin head over a metal edge. Pull the \
bolt assembly away from the firing pin. Place a coin into the slot PIECE OF
near the back edge of the firing pin head. See Picture 18. METAL
4. Hold the bolt assembly and turn the bolt plug counter-clockwise
until the firing pin assembly can be removed from the bolt assembly. ——
CAUTION: Clean the firing pin assembly as a unit. FIRINGPIN —
5. Clean all parts with firearm cleaning solvent. Dry with a clean cloth. HRAD R NOTCH
6. Apply a thin coat of oil. \ \
Al
UNO )
TO ASSEMBLE: /
1. Always point the firearm in a safe direction. BOLT PLUG
2. Place the firing pin assembly into the rear of the bolt assembly. BOLT INCOCKED POSITION

3. Tighten the bolt plug into the bolt assembly with your hand.
4. Pull the coin from the slot in the firing pin head.
5. Turn the bolt plug until the firing pin head goes into the small notch on the rear rim of the bolt. The bolt is
now cocked. See Picture 19.
NOTE: The bolt must be cocked to be assembled into the rifle.
6. Assemble the bolt assembly into the rifle. See instructions on page 9.

16

MODEL 700"

Bolt Action Centerfire Rifle

17

NOOR WY —

PARTS LIST
VIEW PART NAME VIEW
# #

Barrel Assembly 30

Bolt Assembly

Bolt Plug 31

Bolt Stop (Restricted)

Bolt Stop Pin (Restricted)

Bolt Stop Spring (Restricted) 32

Butt Plate

Butt Plate Frame (New Style Not Shown) 33

Butt Plate Insert (New Style Not Shown) 34

Butt Plate Frame Screw (New Style) 35

Butt Plate Spacer

Butt Plate Screw

Center Guard Screw ADL Grade 37

Ejector 38

Ejector Pin 39

Ejector Spring 40

Extractor 41

Firing Pin Assembly 42

Firing Pin Cross Pin 44

Floor Plate Latch, BDL Grade

Floor Plate Latch Pin, BDL Grade

Floor Plate Latch Spring, BDL Grade

Floor Plate Pivot Pin, BDL Grade 46

Front Guard Screw 47

Front Guard Screw Bushing, ADL Grade 48

Front Sight 49

F

MODEL 700"

Bolt Action Centerfire Rifle

ront Sight (Low)

Front Sight Ramp BDL

Front Sight Ramp Screw

Front Sight Hood

Front Swivel Screw

Grip Cap, BDL Grade (Not Shown)
Grip Cap Screw

Grip Cap Spacer (Not Shown)

18

PART NAME

Magazine, ADL Grade

Magazine, BDL Grade (Not Shown)
Magazine Follower, ADL — Short Action
Magazine Follower, BDL

Magazine Tab Screw, ADL Grade
Magazine Spring, ADL Grade
Magazine Spring, BDL Grade

Main Spring

Rear Guard Screw

Rear Sight Aperture

Rear Sight Assembly

Rear Sight Base

Rear Sight Base Screw (2)

Rear Sight Slide

Elevation Screw

Rear Swivel Screw

Receiver Plug Screw

Sear Pin (Restricted)

Stock Assembly, ADL Grade

Stock Assembly, BDL Grade

Stock Reinforcing Screw (Not Shown)

Stock Reinforcing Screw Dowel (Not Shown)

Trigger Assembly (Restricted)
Trigger Guard

Trigger Guard Assembly, BDL Grade
Windage Screw

MODEL SEVEN"

Bolt Action Centerfire Rifle

19

VIEW
#

CO CO NOV A Co D —

— ©

MODEL SEVEN"

Bolt Action Centerfire Rifle

PART NAME

Barrel Assembly

Bolt Assembly

Bolt Final Assembly

Bolt Plug

Bolt Stop (Restricted)

Bolt Stop Pin (Restricted)
Bolt Stop Spring (Restricted)
Elevation Screw

Ejector

Ejector Pin

Ejector Spring

Extractor

Extractor 222 Cal.

Firing Pin (Restricted)
Firing Pin Assembly

Firing Pin Cross Pin

Floor Plate Latch

Floor Plate Latch Spring
Floor Plate Latch Pin

Floor Plate Pivot Pin

Front Guard Spring

Front Sight

Front Sight (Low)

Front Sight Ramp

Front Sight Ramp Screw
Front Swivel Screw

Grip Cap

Grip Cap Insert (Not Shown)
Grip Cap Screw (Not Shown)

20

PARTS LIST

VIEW
#

PART NAME

agazine

agazine 222 Cal.
agazine Follower
agazine Follower 222 Cal.
agazine Spacer 222 Cal.
agazine Spring

agazine Spring 222 Cal.
ain Spring

Rear Guard Screw

Rear Sight Aperture

Rear Sight Assembly

Rear Sight Base

Rear Sight Base Screw (2)
Rear Sight Slide

Rear Swivel Screw
Receiver Plug Screw
Recoil Pad

Recoil Pad Screw

Sear Pin (Restricted)
Stock Assembly

Trigger Assembly (Restricted)
Trigger Guard Assembly
Windage Screw

MODEL 673"
Bolt Action Centerfire Rifle
The ventilated rib, synthetic buffers and rib screws are not shown.

NOTE

21

MODEL 673°

Bolt Action Centerfire Rifle
PARTS LIST

VIEW PART NAME
NO.

Barrel Assembly
Bolt Assembly
Bolt Final Assembly
Bolt Plug
Bolt Stop (Restricted)
Bolt Stop Pin (Restricted)
Bolt Stop Spring (Restricted)
Elevation Screw
Ejector
Ejector Pin
Ejector Spring
Extractor
Firing Pin (Restricted)
Firing Pin Assembly
Firing Pin Cross Pin
Floor Plate Latch
Floor Plate Latch Spring
Floor Plate Latch Pin
20 Floor Plate Pivot Pin
21 Front Guard Spring
22 Front Sight
23 Front Sight Ramp
24 Front Sight Ramp Screw
25 Front Swivel Screw
26 Grip Cap
Grip Cap Insert (Not Shown)
Grip Cap Screw (Not Shown)
29 Magazine
30 Magazine Follower
31 Magazine Spring
32 Main Spring
33 Rear Guard Screw
34 Rear Sight Aperture
Rear Sight Assembly
35 Rear Sight Base
36 Rear Sight Base Screw (2)
37 Rear Sight Slide
38 Rear Swivel Screw
39 Receiver Plug Screw
40 Recoil Pad
41 Recoil Pad Screw
42 Sear Pin (Restricted)
43 Stock Assembly
44 Trigger Assembly (Restricted)
45 Trigger Guard Assembly
46 Windage Screw

D —

22

How to Obtain Parts and Service From RemArms LLC

TO ORDER PARTS:

To order parts please visit www.remarms.com. For additional information on service enhancements, upgrades,
additional barrels and specialty parts visit www.remarms.com.

To expedite your PARTS order or request REPAIR SERVICE visit our web site at www.remarms.com. Detailed
instructions are provided along with parts and/or service order forms.

Please have the following information ready before you email
* Firearm model and serial number.
e Part description and quantity. Part descriptions can be found on the parts listing page in this manual.
* Your complete mailing address (P.O. Box and Street Address) including zip code, telephone
number and e-mail address.
* Method of payment: Mastercard, Visa, Amex or Discover card number and expiration date. Prepayment
may be made by check or money order. A quote may be made to you over the phone. (Sorry, no C.0.D.s.)
WARNING! USE ONLY REMINGTON PARTS IN REMINGTON FIREARMS.

NOTE: SOME PARTS MAY BE RESTRICTED. See parts list for details. Owner's manuals/instruction books may be
requested via our web site at: remarms.com

REPAIR SERVICES

If there is a defect with your Remington firearm that you would otherwise like to discuss with RemArms, please
contact RemArms Consumer Services at www.remarms.com. Please do not send your firearm or other item to
Remington without first (a) calling this number, (b) receiving instructions from the RemArms representative, and
(c) obtaining a Service Request document containing your Service Repair Number. With regards to the Service
Request document, RemArms will either e-mail this document to you or, if you do not have an

e-mail address, RemArms will mail it to you. Please be sure to store your Service Request document in your
records so that it is both safe and accessible.

WARNING! DO NOT SEND LIVE OR SPENT SHELLS IN YOUR FIREARM OR IN THE SAME BOX WITH THE FIREARM. THIS
IS A VIOLATION OF FEDERAL LAW. IF YOU FEEL YOU MUST SEND SPENT SHELLS, PLEASE SEND THEM IN A SEPARATE

PACKAGE AND INCLUDE NAME, ADDRESS (WITH ZIP CODE), TELEPHONE NUMBER, MODEL AND SERIAL NUMBER OF
YOUR FIREARM.

23

Firearm Owner’s Record

Model Serial # Date Purchased

Purchased From Price Paid

A WORD ON THE MAINTENANCE AND CARE OF YOUR REMINGTON FIREARM

Don't Alter or Modify Your Firearm and Have it Serviced Regularly.
Your firearm has been designed to operate according to certain factory specifications. You'll jeopardize your
safety and that of others around you by attempting to alter its trigger, mechanical safety or other mechanisms.
So never alter or modify your firearm in any way.

Like any mechanical device, a firearm is subject to wear. It must be maintained and periodically serviced to
assure optimum safety and performance. Only a qualified service facility should service, repair or modify your
Remington® firearm. Consult your instruction book for instructions on how to send your firearm to the
factory. RemArms recommends that you have your firearm professionally serviced annually. You should also
have your firearm professionally serviced after prolonged storage, or if there is ever any question pertaining
to the proper functioning characteristics of your firearm.

Proper cleaning and lubrication are also important to firearm maintenance and are necessary to assure accu-
racy, Safety and reliability. Before cleaning, always make sure that your firearm is completely unloaded. And
always clean the barrel from the chamber end to the muzzle when possible.

24

Firearm Maintenance Record

SERVICE PERFORMED PERFORMED BY

25

Notes

26

Notes

27

Remington.

REMINGTON IS A TRADEMARK REGISTERED IN THE UNITED STATES PATENT
AND TRADEMARK OFFICE

PART No. 3509
PRINTED IN U.S.A. RD FORM RD 7055 REV. O3/21